Questions.?

ChlorFree-AquaSmart

CRYSTAL CLEAR, CLEAN, SOFT, FRESH "IONIZED" WATER

with 'Tasha'

"Since using ChlorFree Filters in our Pool, I'm no longer afraid of my Hair turning Green." 

Thank you for a Wonderful Product, Tasha.

™ "Water Purification Filters"!

“As EASY as 1... 2... 3.”

  1.  How do we maintain a ™ Swimming Pool, Hot Tubs or Jacuzzi.?

  2. Where do we place your ™  Filters?

  3. How do we Raise the pH of our water?

  4. How do we convert to  ™  from Baquacil, Bromine or a Salt (Chlorine) Generator?

  5.  How can we Test for Calcium in my Chlorine?

  6.  Will we need to SHOCK our Pool or Jacuzzi?

  7.  How can we Test for  ™  Ionization?

  8.  What if our  ™  Pool is Seasonal?

  9.  Will  ™  Corrode or Stain my Pool? 
 

  10.  How does  ™  compare with other forms of Water Treatment?

  11.  How does  compare to Salt (Chlorine) Generators, 'Nature2' or 'Floatron'?

  12.  How can we eliminate Suntan and other Oils from our  ™  Pool?

  14.  Why is your product only available outside the States.?

  1.  How do we maintain a ™ Swimming Pool, Hot Tubs or Jacuzzi.?

During the First ChlorFree-AquaSmart month, we suggest that you keep track of your progress by using our 30-Day ChlorFree-AquaSmart History Report.  After the first few days, your Pool or Jacuzzi will seem to maintain itself and the rest will be quite easy.  ChlorFree-AquaSmart Ionizing properties have no effect on either raising or lowering the pH however, Ionization does require that your pH for ambient temperature pools remain close to Neutral (below 7.4) and below 7.6 for Heated Pools or Jacuzzi's. 

Heated Water as with Jacuzzi’s, produce considerably more Bacteria and consequently need additional disinfection as compared to Ambient Temperate Water.  Therefore, we’ve designed our ChlorFree-AquaSmart Ionizing Capsules to produce enough ‘concentrated’ Ionization to Safely Disinfect your Jacuzzi from Harmful Bacteria and Viruses.

There are basically only Three (simple) 'Keys' to maintaining a ChlorFree-AquaSmart Pool or Jacuzzi:
       1.  Maintain the pH near 'neutral' (below 7.4) and for Heated Pools/Jacuzzi's, between 7.4 - 7.6
       2.  Maintain Good Circulation by backwashing at least twice a week and run your Pump 7-8 hours and Change the components in your (sand or membrane) Filter as required.
       3.  When 'New Water' is added (rain or refilling) by more than 1/4" as new water is generally contaminated, add a little chlorine 1.0ppm for the day.

 

  2. Where do we place your ™  Filters?

The Success from ChlorFree-AquaSmart was built on the "KISS Principal”.  We provide our Customers with a Product that is, "Easy to Use, Inexpensive and offers a 'Remarkable' Difference.

The ChlorFree-AquaSmart Filters are very Simple to install, Very Inexpensive and is Easy to use.  Simply, place our  (3") ChlorFree-AquaSmart Capsule's into your Skimmer or anywhere where they can remain Submerged where water circulates.  For Pools or Jacuzzi's without a Skimmer Basket, our Filters can be simply placed anywhere near a Bottom Drain. 

  3. How do we Raise the pH of our water?

We do not recommend using Baking Soda (Sodium Bicarbonate) as raises the pH very quickly and consequently needs to be used with small amounts.  Unlike most people who are unfamiliar with using this material in order to raise their pH ‘Slowly’, by raising it above 7.6 in ‘ambient temperature’ pools and 7.8 in ‘Heated’ Water to a high alkaline level, Ionization will quickly become depleted therefore, loosing the Effectiveness of the ChlorFree-AquaSmart Ionization Properties. 

There are also side effects associated with absorbing Sodium Bicarbonate which result in metabolic alkalosis which is associated with muscular Twitching, Irritability and Tetany (tingling) and possible Hypernatremia (excessive sodium in the blood).

We suggest using a Calcium Based or Sodium Based Chlorine (in very small amounts) until the desired pH level is attained.

  4. How do we convert to ™  from Baquacil, Bromine or a Salt (Chlorine) Generator?

"I finally had my fill of Baquacil. I later learned that it was in many ways as unhealthy as Chlorine."

Bromine has the atomic number 35. Like chlorine, it is a halogen and it easily reacts with other elements. In nature bromine can only be found in compounds. These combinations are called bromides. Bromides are used to obtain pure bromine and to produce bromine products. After fluorine, bromine is the most reactive element. It reacts with many different substances, is very corrosive and destructive on organic material.  

Bromine is a bleach. It is poisonous in fluid form and bromine vapor is destructive for the human skin, eyes and respiration tract. It causes serious burns. A concentration of 1ppm can cause eye watering and when inhalation of concentrations below 10ppm occurs, one starts to cough and the respiration tracts are irritated.  Bromine concentrations around 0.5 mg/L in swimming pools cause eye and mucous membrane irritation and can lead to odor nuisance.  Bromine is used as a disinfectant, because it is harmful for microorganisms. When organic bromine enters surface waters, it has negative effects on the health of water fleas, fishes, lobsters and algae.

Bromine (Br₂) is not used in drinking water treatment where as ChlorFree-AquaSmart is used for Water Treatment.  Bromine reacts far to quickly with organic substances, and no residue will remain. Bromine gives drinking water a terrible medicine-like taste. Bromine should only be used in emergency cases.

Bromine is very reactive. In order to maintain an adequate disinfection, the amount of bromine that is added must be very high. Bromine aggressively reacts with metals and it is a corrosive material.  Security measures should be taken when bromine is transported, stored or used.

ChlorFree-AquaSmart actually 'replaces' the need to Baquacil however, if you prefer maintaining your Pool with Baquacil or your Salt (Chlorine) Generator, you can however, if you prefer not to, you only need to gradually filter out this product or turn off/down your Salt Generator which will be replaced by the properties of ChlorFree-AquaSmart Ionization.

  5.  How can we Test for Calcium in my Chlorine?

Chlorine containing Calcium such as Calcium Hypochlorite will raise your pH however, Trichlor Chlorine has a Stabilizer which helps to maintain your pH.  Trichlor is available in both Tablet and Granular form however, we recommend using Tablet form as it slowly dissolves and only needs to replaced every 4-days.

The following a Simple Test to see if there is a presence of Calcium in your (granulated) Chlorine which will cause the pH in your Pool or Jacuzzi to Rise.

1.  Take a pH reading using your 2-Part Pool Test Kit.
2.  Place a very small particle of your Granulated Chlorine in the pH Side.
3.  Gently Rock the Chlorine Grain very slowly back and forth and
4.  If the Color Changes to Bluish or Purple color or the pH Reading rises, you've got Calcium.

 

  6.  Will we need to SHOCK our Pool or Jacuzzi?

Chlorine SHOCK is an 'Oxidizer' that is generally used to "Dissolve" Organic Material.  After ChlorFree-AquaSmart 'Neutralizes' Microscopic Organic Material, the Dead Organic Material is left to either Filter out or to be 'Oxidized'.

If you do find the need to occasionally SHOCK your Pool or Jacuzzi, we strongly suggest not using your Pool or Jacuzzi until your Chlorine level has diminished below 1.0ppm

  7.  How can we Test for  ™  Ionization?

 

The moment that your ChlorFree-AquaSmart Ionizing Filters are immersed in water, they slowly begin to release minute quantities of invisible negatively charged particles into the water. Within a period of only 24-hours, charged ions begin to infuse into the water to Virtually Eliminate the need for Chlorine and other Chemicals for Pools & Jacuzzi's.

The ChlorFree-AquaSmart Ionization System utilizes an advanced process known as ionization, whereby electrolytically generated copper and silver ions are dispersed into a water stream for the purpose of Virtually Eliminate the need for Chlorine and other Chemicals for Pools & Jacuzzi's.  Once the Ionization System is commissioned (submerged), the concentration of ions builds quickly within the system, producing a long and stable disinfecting residual that is unaffected by heat, sunlight or evaporation. The disinfection action is attributed to the positively charged ions which form electrostatic bonds to the negatively charged sites on microorganisms and then undergo reactions at the cell surface, crossing the cell membrane and beginning the inactivation.

ChlorFree-AquaSmart was originally designed as a Water Purification Submersible Ionizing Capsule/System that releases Ions to eliminate all forms of Bacteria and Virus, E.Coli, etc.  Our Technology requires no electricity or special installation as it is simply placed into a Water Tank, Well, Cistern and most commonly used for Swimming Pools, Jacuzzi’s and Fresh Water Aquariums.  ChlorFree-AquaSmart Technology is quite effective for populations with a high degree of Bio-Contamination and where the use of Chlorine is either unavailable or ineffective.  http://chlorfree.net/waterpurification-2_files/Africa%20Testimony.doc 

ChlorFree-AquaSmart was implemented with the Community of Flamingo Beach in September of 2000 and according to their City Officials, they boast in having, “The Best Water in the World”.  http://chlorfree.net/WaterPurification.htm

Another 'Clear' benefit from using ChlorFree-AquaSmart Filters is the ionization properties generated by these Filters attracts Suspended Dust and Debris that continually enter your Pool and precipitates the coagulated dust particles to the bottom of the Pool. The ionized particles that are generated from these Filters, actually maintain a Sparkling Crystal-Clear appearance 24 hours a day, all year long.  ChlorFree-AquaSmart provides a Healthier environment for your Family and according to our EPA Certification, is a completely safe form of Water Purification.

Testing for the presence of Ionization is quite simple as there are 3-distinctive ways to Test for Adequate Ionization Saturation.

1. The Quality of the Water will maintain a 'Rich Bluish' appearance.
2. The Quality of the Water will maintain a 'Soft and Silky' Feel to the Touch.
3. The Quality of the Water will maintain 'Sweet, Clean and Soft' Taste.
4. The Surface of the Water will maintain a ‘Sparkling Clear’ appearance.
5. You will actually ‘See, 'Feel and even Taste’ the ChlorFree Difference.

We have found that the 'Watersafe® Rapid Bacteria Test Strips' offers an inexpensive Do-it-yourself (20-minute) Bacteria Test Kit quite useful for Testing Potability.  Their Website is: www.discovertesting.com/products/display_products.sd?iid=44&catid=8&loc=show&headTitle=Watersafe®%20Rapid%20Bacteria%20Test%20Strips%20Box%20of%20Ten

  8.  What if our  ™  Pool is Seasonal?

 

If you prefer, you can remove your ChlorFree-AquaSmart Ionizing Filters during your Winter Season and store them in a Dry place.  Once the Filters are taken out of the Water, they will Hibernate until they are reintroduced back into the water. 

If you have a 3-month Pool Season for example, your ChlorFree-AquaSmart Filters will essentially last for 4-Full Years.  When you replace your ChlorFree-AquaSmart Filters back into your Pool, you’ll only need to re-Ionize your pool as you did when you first received your ChlorFree-AquaSmart Filters.

 

  9.  Will  ™  Corrode or Stain my Pool? 
 

Corrosion:  Most Pool Owners agree that ChlorFree-AquaSmart Replaces the need for <corrosive> Chemicals therefore the Surface, Pump and Equipment lasts 'Considerably' longer. 

The Ionization System provides certain unique advantages over traditional "chemical only" water treatment. Unlike most halogens and biocides, ions provide a stable, measurable disinfecting residual that is unaffected by water quality, heat or evaporation. The Ionization System does not accelerate corrosion rates, as do most oxidizing agents, and can actually reduce the use of these chemicals up to 90%. Savings in chemical use, plant preservation and labor offer the end user rapid pay backs. The handling and storage of potentially hazardous materials are also greatly reduced, and therefore so is the associated liability of handling Hazardous Corrosive Chemicals. 

Staining:  The 'maximum' Cu (Copper) saturation level that ChlorFree-AquaSmart Ionizing Filters produce is 0.15ppm which is 85% less than EPA 1.3ppm Maximum Copper Saturation Standards however, excessive amounts of Copper, can deposit itself on these surfaces, giving a "Roman-Tub" blue-green appearance, which by the way, isn't too bad to look at as many Pool Owners actually prefer the blue-green color which was commonly prevalent in Mineral Baths. 

ChlorFree-AquaSmart, maintains such a low Copper Saturation Limit (Less than 0.15ppm - or 85% lower than EPA’s Maximum Standards for Potable Water) that the amount of Copper allowed to permeate the pool is minimal and barely noticeable.

Heavy metals left in the pool:  Heavy metals play very important roles as cofactors in ionization, stabilization of protein structures, electron transfer and water ionization. Certain heavy metals like Lead, Copper, Mercury and Cadmium however, are toxic even at very low concentrations according to EPA Maximum Potable Limits in excess of 1.3 ppm (http://www.epa.gov/safewater/dwh/c-ioc/copper.html).  ChlorFree-AquaSmart maintains a Copper Saturation Limit of ‘Less than 0.15ppm which is 85% lower than EPA’s Maximum Standards for Potable Water. 

Many have asked us, "Should water chemistry be a concern ( water hardness, total dissolved solids, total alkalinity) in a ChlorFree-AquaSmart pool?"   A.  Water Hardness is caused by water that contains Calcium therefore Chlorine that also contains Calcium only adds to Water Hardness.  Total Dissolved Solids (TDS) is from dust, dirt, metals, minerals and debris that remains Suspended in the water.  One of the Many Benefits from ChlorFree-AquaSmart is from the Ionization Properties that is generated from ChlorFree as Ionization Magnetically ‘Coagulates’ (attract) this suspended/dissolved material and Precipitates it to the bottom of the Tank, Well or Pool

  10.  How does  ™  compare with other forms of Water Treatment?

Ionization - Chlorine - Ozone - Ultra Violet - Reverse Osmosis - Infrared, etc.

The Following Chart offers an in depth Comparison between most common types of Biocides.

 

http://www.nosoweb.org/infectious_diseases/water_table.htm

  11.  How does  compare to Salt (Chlorine) Generators, 'Nature2' or 'Floatron'?

ChlorFree-AquaSmart vs. the Competition

Ecosmarte (www.ecosmarte.com) as any 'Electrical' Ionizing Systems require ‘110v Electrical Current’ and of which I would not ‘Swim’ in (Electricity and Water do not mix) and is not a practical, easy or Safe choice. Unlike ChlorFree-AquaSmart Ionizing Filters, these Systems require ‘Electricity’ require both a Qualified Electrician and a Plumber to install. Most require High Concentrations of Salt to be added to the Pool which electrically, produces/manufactures Chlorine and these Systems are also very expensive. An average pool will cost between $1,200.00-$4,500.00 (plus installation) and the ‘Submersible 110v - 12v Electrodes’ will need to be changed every 3-4 months.

Other Electrical Ionizers, http://www.sunshinepool.com/ion1.html also require a 'Direct' 110Volt Electricity and Special Installation (Qualified Electrician and Plumber) which needs to be converted to 12v before wiring this Electrical Current directly into the Pool Water. These Ionizing Systems require hundreds of pounds of Salt to be added to the pool and constantly added to maintain salt levels every 3-4 months. These electrical Ionizing Systems generate CHLORINE by converting Sodium (SALT) to Bromide and then to Chlorine.  They don’t eliminate Chlorine, they actually make CHLORINE.

There are only a few (non-electrical) Ionizing Systems on the Market that do not require electricity, 'Nature2' (www.Nature2.com), ChlorFree-AquaSmart Ionizing Filters and 'Floatron' (www.floatron.com) which is a device that Floats on the surface of the Pool and requires ‘constant’ Sunlight to operate.

Nature2 does not require Electricity to operate. The Nature2 System incorporates a housing that requires the Pool's Return Water-Line Tube to be Drilled and the Devise is Clamped on to the hole that's Drilled into the Tube. Because of its Design, Nature2 only Operates when the Pump is running and unlike ChlorFree-AquaSmart which is remains submerged in the Skimmer, Nature2 offers no accumulated Ionization.

"Floatron" is a 'Floating' Solar Powered Ionizer that depends on Solar Power to generate electrical current to drive it's Probes which are submerged below this device. There are two problems associated with this device. One is that does not generate enough Ionization as claimed and the other is because it's usually in one area 'downwind' of the pool, what little Ions it does produce, remains concentrated in only one area. Andrew Arata who is manufacturing a Liquid Ionization 'Disinfectant' (Axenohl) headed the Floatron Research who commented that because this device is generally pushed and remains Downwind of the pool. The problem he has found with a Floating Solar Powered Ionizer is that it is free to move around the pool thus leaving 'Ion Pockets' where it generally remains which is predominantly downwind of the pool which and does not allow for Ion Distribute throughout the pool. In other words, this System will not 'Ionize' the entire pool as it most prevalently remains where the Wind pushes it - Downwind.

Ions need to be circulated and if left without Circulation, the System fails. Floatron and Nature2 cannot generate enough Ionization needed to maintain a Residue or enough Saturation for their System to work properly and with respect to Nature2 it only works when the Pump is on which is why their Systems 'needs' a considerable amount of Chlorine.

ChlorFree-AquaSmart requires NO Electricity or Special Plumbing or Chemicals other then Muriatic Acid used to 'Reduce' the pH and a small amount of Chlorine when New (Contaminated) Water is Added or if the Pool/Jacuzzi is Frequented and especially by Children (Pee).

Unlike the Electrical (110v) Ionizers which most require the use and constant maintenance of adding a lot of Salt, ChlorFree-AquaSmart requires No Electricity, Plumbing or Salts (Salt is converted to Chlorine) to operate and is Simply replaced Yearly. Since ChlorFree-AquaSmart is constantly submerged (in the Skimmer), it 'always' produces Ionization and when the pump is turned on, the concentrated collection of Ions that have built up in the Skimmer are immediately Injected into the Pool - Evenly and Throughout by means of the Pools 'Return-Jets' and are mixed throughout the rest of the Pool or Potable Water Reserve (tank) and mixes with the existing Ions that are lest in residue. Therefore, there is no lack of Ionization and is distributed throughout the Pool on a daily basis.

ChlorFree-AquaSmart is a 3" Submersible Capsule that links together when more then 1 is needed and is Simply Placed into the Skimmer or anywhere where is remains submerged, and constantly produces Ionization while submerged and remains active in the Skimmer allowing the Ions to accumulate. Ions produced by ChlorFree-AquaSmart has a Useful Life of 1-year which means these Ions produced by this Devise can be Bottled and Stored for up to 1-year. See: How ChlorFree-AquaSmart Works at: www.ChlorFree.net/Why.htm You'll Especially enjoy reading the Benefits from Swimming/Bathing in Ionized Water.  Reference: "Water & Ions for Life" found in this Section.

ChlorFree-AquaSmart maintains its Ionizing Properties 24-hours a day as long as it is submersed in water and when the pool pump is turned off, the Ions will then accumulate in the skimmer basket (where the ChlorFree-AquaSmart Filters are located). Ionization is re-injected and circulated into the Pool when the pump is turned and remains on.

The obvious difference with the ChlorFree-AquaSmart System is that the ChlorFree-AquaSmart Filters are simply placed into the Water and continually produces ionization which is distributed throughout the pool. When used in a Swimming Pool, circulation is achieved by means of the Return-Jets. For Potable Water, circulation is achieved by water entering the Tank and when it is consumed.

As you can see, all of these ‘Ionizing’ Systems for the exception of Nature2 or the ChlorFree-AquaSmart Ionizing Filters, either require a Source for Electricity, Special Installation or as noted with Nature2 and Floatron, are not nearly as effective as the ChlorFree-AquaSmart's Submersible Capsule and none of these Ionizing Systems are recommended for Potable (Consumable) Water except for the ChlorFree-AquaSmart Water Purification System.

The ChlorFree-AquaSmart Philosophy and the Success of our Company was built on the "KISS Principal”. Keep it Simple and as you 'clearly' see, the ChlorFree-AquaSmart Filters are Simple to install, Inexpensive and is Very Easy to use.  In my opinion and years of having a Swimming Pool and a Jacuzzi, the ChlorFree-AquaSmart is 'Simply' the Best CHLORINE Alternative as compared to any other System available on the Market today.

Unlike these other Ionizing Generators as mentioned above, ChlorFree-AquaSmart is now being used to 'Purify' the Drinking Water for Municipalities.  See:  www.chlorfree.net/waterpurification.htm

  12.  How can we eliminate Suntan and other Oils from our  ™  Pool?

Accumulated Surface Oils are caused either from Bathers who 'forgot' to remove Suntan Oil before entering the Pool or your Swimming Pool is located nearby Heavily Traffic (Polluted Air) or located near an Airport. 

In order to Effectively remove/dissolve accumulated Oil from the Surface of your Pool, simply mix 1-part Liquid Dishwashing Detergent with 9-parts water and using an ordinary Spray Bottle, simply Spray the diluted detergent over the entire surface of your Pool.  You can actually 'see' where the Oils are Dissolving at the Surface from the Reflection of the Sun.  (KISS).

  Troubleshooting Guide: 

Click Here

Commonly known Problems associated with 'Normal' Pool Care...

T R O U B L E S H O O T I N G

and
Helpful Hints Guide
Easy as...